Home / Best 3D Products / CNC Shield + UNO R3 Board + 4 X DRV8825 Driver Kit For Arduino 3D Printer

CNC Shield + UNO R3 Board + 4 X DRV8825 Driver Kit For Arduino 3D Printer


Price: $32.00

DRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 – 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) – Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Package included: 1 x Uno R3 Board 1 x CNC Shield Board 4 x DRV8825 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row NeedlesDRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 – 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional
cooling). Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with
a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) – Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O p
ins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Package included: 1 x Uno R3 Board 1 x CNC Shield Board 4 x DRV8825 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Needles


About angle meth

Check Also

O&W (3D)Printing Lovely UV Fish Headwear Bandana Balaclava Neck Gaiter Helmet Liner Face Mask.For Cycling Hunting Riding Running and Outdoor Actives Pack of 1 ¡­

O&W (3D)Printing Lovely UV Fish Headwear Bandana Balaclava Neck Gaiter Helmet Liner Face Mask.For Cycling Hunting Riding Running and Outdoor Actives Pack of 1 ¡­

Price: Our product is used 3D printing technology,it’s will be show perfect VFX.And we used …

Leave a Reply

Your email address will not be published. Required fields are marked *